Battery Condition Tester (Identifier & Regenerator & Discharger)

Model : RPT-T300

Renewable Energy by Green Technology

All New HF Pulse Innovation

PRIME Battery Regenerator adopted the most innovative High-Frequency Pulse technology which is proprietary developed by the cutting-edge technology of REPOWERTEK.

SOLAR, UPS, Electricity, Telecom Tower, Military, Eco Town, Electric-Forklift, Golf cart, Wheelchair, Lift & Scrubber, Automotive Vehicle, Heavy Equipment, Agricultural Equipment, Marine Boat, Train, etc.

RPT-T300 Battery Condition Tester & Regeneration System (7-in-1 Multi-functional Regeneration System) is a special all-in-one Battery Condition Tester for 6V~12V lead-acid batteries. It supports multi-functions of digital Regenerator + Charger + Discharger + Power Supply + IR & CCA Checkers + Battery Condition Tester up to 300Ah at 12V batteries. A 12V battery is composed of 2 volts x 6 cells. Before a restoration process, it is hard to know about the shorted circuit, cell cut, cell corrosion state, and any damaged cells. For this reason, the other competitors must only check on these damaged cases after finishing a process. So, we have developed on 'RPT-T300'. It can find the short of electrodes and damaged cells within a few minutes before the restoration procedure. Automatic battery condition test function (whether to be restored or not - by 'CONDITION TEST' mode). Using it, most batteries will assort for targeting ones to be regenerated with our new RPT-T300 if they do not have any cell cut or short and internal cell damage (corrosion). RPT-T300 has a fully automated function to regenerate by setting voltage and Total capacity only.

Functional Modes

1. Regenerator (6V~48V all adjustable voltages-in-one, 40Ah~ 400Ah capacity) at 'REGENERATION' mode 2. Charger (6V~48V all adjustable voltages-in-one, Up to 400Ah capacity) at 'CHARGE' mode 3. Power Supply (6V~48V free setting mode of Voltage, Current & Time for special & sleeping batteries)

* Mainly used for 2V Reach Forklift, TELECOM UPS & other Traction bank/rack connected batteries

* Mainly used for 12V bank connected batteries up to 48V (4 x 12V batteries at the same time).

* Maximum Limited Output Current : 6V~48V = 30A

* A Discharger (RPT-D10K) is optional.

Specifications

RPT-E400 (3-in-1) : 230mm(H) x 345mm(W) x 440mm(D), Approx. 17kg

Variable Application

All kinds of 6V ~ 12V lead-acid batteries including VRLA & Deep Cycle

Restoring and recharging up to 300Ah battery capacity

Optimization of operation conditions for all countries

Lowest power consumption using SMPS with switching control

AC80 ~ 120V / 210 ~ 250V Compatibility

Smart Control System by Micom

Control minute electric current & Voltage depending on the type of battery Restoring and recharging for small capacity (40 ~ 300Ah) batteries

Minimizes damage to electrodes and restrain accumulation of sulfate on electrodes

Optimized high frequency pulse with charging curve algorithm

Optimized charging and restoring algorithm

Utilizes special pattern information on various battery kinds and characteristics

Adopted on the optimized high-frequency Pulse

Prevents electrical / physical damage when restoring and charging batteries

Prolongs battery lifecycle 2~3 times

Wide Application Range

Can regenerate and charge high-capacity batteries (Max.300Ah) Can discharge all of 6V ~ 12V batteries (Max. 420W) Can condition test all types of lead-acid 12V batteries (DC 12V only)

Can restore and charge GEL and AGM VRLA type batteries Can measure Internal Resistance and CCA twice (before & after)

Can set up values manually as a high-end power supply

Safety

Prevent from higher battery temperature by output voltage and current control

Maintains low battery temperature during restoring (Input Over - voltage Protection)

Stable current / Voltage supply (Control input voltage variation function)

Prevents potential hazard caused by high battery temperature