Home
/
Categories
/
Chemicals
/
Adhesives & Sealants
/
Construction Adhesives
/
CSA Cementious Self-Leveling Material
CSA Cementious Self-Leveling Material
FOB Price
Port
Tianjin
Lead Time
within 20 days after confirmation
China
Main Products : Rapid set cement, High strength cement, concrete mortars, concrete repair material, Non-shrinkage grouting material, CSA binder, CSA cement, CSA Expansive
Yujing East Road Beijing, Beijing
CSA Cementious Self-Leveling Material Details
Brand Name
Polar Bear
Place of Origin
China
CSA Cementious Self-Leveling Material Introduce

CSA Cementious Self-Levelling Material

General characteristics

Polar Bear cementitious self-leveling materials consist of a blend of selected cements, superplasticizer, and aggregates modified with polymers and flow agents. It is used in conjunction with Polar Bear Primer. Polar Bear cementitious self-leveling materials are supplied as pre-blended powder which requires only the addition of water on site to produce a self smoothing, free flowing material. These materials are designed for installation by a continuous mixer pump, but can also be applied by hand. Functionally they are divided into two categories: underlayments (CSA-II and CSA-III) and overlayment (CSA-I).

Properties

Fast application by pump, enables large areas of floor to be completed in a working day. Rapid hardening and curing allows speedy access for foot traffic and overlaying with carpet, vinyl etc. One pack product, applied by pump eliminates on-site batching and ensures consistency of mixed product. Dimensionally stable, can be installed in large areas Excellent adhesion to prepared substrates Environmental friendly.

Data

Table 1 Specification of Polar Bear Self-leveling Materials

Standard Grade F10 C30 F10 C30 F10 C30 F6 C25 F4 C20
Name CSA-I color CSA-I CSA-II CSA-III CSA-IV
Setting Time I.S.,min 100-120 100-120 100-120 60-90 90-100
F.S.,min 120-150 120-150 120-150 100-120 100-120
Compressive Strength
(Mpa), ≥
1 day 6.0 6.0 6.0 8 8
7 days 20 20 20 15 15
28 days 30 35 30 25 20
Drying Shrinkage, % <0.10 0.05 <0.05 <0.05 <0.05
Bonding Strength (Mpa) 1.0 >1.0 >1.0 >1.0 >1.0
Flow Initial 130 mm ≥140 mm ≥145 mm
After 20 min ≥130 mm ≥130 mm ≥130 mm
Working Life ≥ 20 min
Application Temperature 5-30 ℃
Walk-on time 8 h 3-4 h
Time to overlaying 1-3 d 1-2 d 1-2 d 1 d 1 d
W/P ratio 0.18 0.18 0.20 0.25 0.24
 
Application area

Application method

Preparation

The substrate should be clean, sound and free from loose material and contamination such as plaster, oil, paint and grease. The substrate should have a compressive strength of at least 20 MPa and a surface tensile strength of at least 1MPa (pull-off strength). Excess laitance should be removed by mechanical methods followed by vacuuming and water cleaning to remove dust debris. Oil and grease can be removed by chemical detergent followed by water cleaning. New concrete should be at least 14 days old. In case of porous substrate or hot weather, the substrate should be ponded with clean water for 1~3 hours before priming.

Priming

The object of priming is to seal the substrate to prevent air release from the subfloor rising and forming bubbles and pinholes on the surface. Extremely porous substrates may require two priming/sealing coats. Primer coats must be allowed to dry before applying the self-levelling material.

Pumping or Mixing by hand

This is a specialized activity and the product must be applied by a recommended contractor who has been fully trained in the use of the product and equipment. 2. In case of installation by hand, pour the mixing water into the clean mixing vessel. Add the whole bag of powder slowly to the water, mixing continuously with a heavy duty drill fitted with a suitable paddle. Mixing should continue for at least 3 - 5 minutes

3. Whatever pumping or mixing by hand, make sure that a smooth creamy consistency is obtained.

4. Do not mix more material than can be reasonably laid within the flow time of the material.

However, ensure that subsequent mixes are ready to enable continuous pouring.

Pouring

1. Make sure there is no ponding of primer before pouring the material.

2. Pump should be used for large area application.

3. Pour the mixed material on to the dry primed surface, spread with trowel and allow to self-smooth. Roll surface with the purpose made spiked roller. Best results are achieved when the pouring and leveling is a continuous process.

Cleaning

The material should be removed from tools and equipment with clean water immediately after use. Hardened material can only be removed mechanically.

Curing

Curing is not essential normally. But in case of high environmental temperature, direct sunlight or windy weather plastic sheet should be used to cover the hardened surface for 2 days.

Estimation

Package
Self-leveling material 25 kg/bag
Primer 50 kg/bucket
Consumption
Self-leveling material 1.7-1.8 kg/m2·mm
Primer 5 m2/L/2 coats

Coating

In areas that are subjected to regular water immersion or chemical attack from acids or organic solvent, it is recommended to protect the self-levelling material with an epoxy floor coating. For more information please refer to the technical support of Polar Bear.

Limitation

Concrete substrate onto which the self-levelling material is to be applied must have a surface temperature of at least5℃, with the air temperature of at least 10℃.

Avoid direct sunlight onto the applied floor or wind blowing over the floor surface during application and the initial stage of curing.

When used as an overlayment,an appropriate sealer should be used to enhance the wearing resistance as well as the color shade.

Storage

Polar Bear self-leveling material should be stored on pallets in dry conditions. Under these conditions the product will have a shelf-life of 6 months.

Part of projects

Beijing Benz-Daimler Chrysler Automotive Ltd. (BBDC)

Beijing 301 Hospital

Beijing Siemens Group

Beijing Zhongguancun Putian Plaza

Changde cigarettes factory

Tangshan Ronghe Jingyuan

CCTV data center

Beijing Tongzhou district Luhe hospital

Beijing Baiziwan New city building sale house

Changchun Eurasian Mall

Tangshan Chuangyuan Fangda instruments Co.,Ltd warehouse

Beijing Chuangjia Printing Company

Beijing Yifei electric warehouse, worker’s canteen

Beijing Baodaming decorate company office department

Beijing Zhuoda University Hall

Note: Edit by Jack Young,as references only. For more informations, please contact: yangjian1886 (Skype)

Previous : 1,2-EPOXY-4-vinylcyclohexane Cas No 106-86-5 Next : Wall Putty Powder
Copyright 2023-2024 - www.globalbiz8.com All Rights Reserved