Chair Upholstering Machine for Stationary Chair

Feature:

1. Greatly increase working efficience for upholstering of office, kitchen and other chairs;

2. Models for upholstering of bed screen, stools, sofa pedal, stationary chair surface are also available by request;

3. To achieve better effects, moulds made of foam, wood, or other hard materials are recommended according to the chair to be upholstered respectively.

Application:

Only qualified personnel should be allowed to operate this device

Note: Don't connect to power supply before completion of adjusting and installation

Installation

Place the table on hard, level surfaces, or you have to upgrade floor condition. If necessary, bolt it to the surface.

Air supply

The air pressure ranges from 6 to 8 bars. A water-extractor is needed between the machine and an air compressor. If the air pressure is greater than 8 bars, then an air pressure reducer is needed between the machine and an air compressor.

Note: It is only proper that the air pressure is between 6 to 8 bar, which will ensure the flexibility and safety of your operation.

Operation

Connect an air compressor to the machine with an unblocked air tube, and then you can begin to operate the machine.

Adjustment of height between two pressing pans

The distance between the two pans is adjustable by turning the lead screw.

Maybes when upholstering

There are three maybes that may occur:

a. No mould is needed

b. Foam mould is needed;

c. A specially made mould is needed

In any case, you can adjust the distance between the pans or the pressure of the upper pan or both of them to achieve the best upholstering effects.

1) Foams

It is inefficient to use a mould when output is small. The mould cushion should be made of compressible foams. We recommend using mould cushion made of different types of foam glued together to achieve the best upholstering effects. In addition, these foams must be soft and big enough, that is to say, they should be bigger than the workpiece bet smaller than the machine beam, and otherwise you can't turn them around while stapling.

2)Making special moulds

In the following 4 situations, special moulds are needed

a. A high quality demand

b. Each side of work piece has different curvatures.

c. Work piece is multi-layered

d. There is no need to amend the mould frequently

There are four threaded holes in the base pan, which are used to bolt mould base plate to the pan.

Operation procedure

Notes: The manual valve only controls the movement of the cylinder and the upper pan, as soon as you turn off the lever, the upper pan stops immediately. We suggest necessary precautions be made for your safety while working.

Operation steps:

a. Put workpiece on the mould, making sure it is covered by foam and other upholstering materials

b. Turn down the valve stem to make the pan moves down to compress the workpiece.

c. Stapling. Staple the workpiece as usual, and you can turn the workpiece while stapling.

d. Turn the valve stem upwards to lift the pressing pan.

Air pressure adjustment

Method: lift the black knob on the valve and keep turning it clock-wise to reduce air pressure to an appropriate level, then press it down to lock it.

Maintenance & repair

1). Maintenance of the air -pressure reducing valve

Lubricating the "o" rings: switch off the air supply, making sure no compressed air exists. Opening the top of the valve and removing the cone shaped component, then you can lubricate it with care.

2). Maintenance of the filter:

Release condensed water regularly, and change another one if needed

3). Change filter

Removing the water container and unscrewing it, replace the old one with a new one. Remember to check its suitability

Special mould making

a. Decide upon the sizes of the mould base plate according to the size of workpiece.

b. Mould base can be made of a 12-16mm thick fiberboard, which is 60mm bigger in size than the workpiece.

c. The frame above the base plate can be divided into four parts. You can shape them by milling or other ways, then assemble them together as following:

Shenzhen Xinqunli Machinery was established in January 1995, is the first professional engaged in developing and manufacturing of sofa making machinery. Xinqunli committed to its mission "Dedicate itself to innovation, pool the wisdom and efforts of everyone" in order to achieve industry upgrade. And, to give further impetus to the sofa industry by standardization, mechanization and use of advance information technology.

Xinqunli' s products has obtained the ISO9001 international quality system certification, CE product certification, they passed the detected quality indicators of the National Woodworking Machinery Testing Center as well as awarded a number of national technical patents. Moreover, Xinqunli ha professional technical teams which provide wide range of services, such as technical advisory and manufacturing workflow planning consultation. It alson supply professional sofa making machinery. As an industrial leader, the Company not only owns over 80%of the market share in the PRC, but also has significant amount of export sales.

Packaging & Delivery

Packaging Details:

wooden packing as export standard

Delivery Detail:

7-15 working days after payment

FAQ:

1. Q: Can I get some samples?

A: Yes,sample order is available for quality check and market test.

2. Q: How long is the warranty period ?

A: Non-artificial damage, one years warranty

3. Q: Do you have the products in stock?

A: Yes ,of course

4. Q: Freight Cost?

A: The shipping cost depends on different weight;

We will choose the cheapest and safest way according your detail quantities.

5. Q: How does your factory do regarding the quality control?

A: Quality is priority. Every product will be fully assembled and carefully tested before packing and shipping.